I had someone call me last month convinced their charger was dead. Completely dead. Turned out to be a tripped RCD at the consumer unit, fixed in about thirty seconds once an electrician looked at it. That’s the thing about “my charger’s broken” calls: most of them aren’t that at all.
So before you brace for the worst, here’s what I want you to know. Nine times out of ten this comes down to one of a handful of repeat offenders, not a dead unit. I’ll walk through what they are, what usually causes them, and which ones are safe to poke at yourself versus which ones genuinely need an electrician standing in front of the thing.
When There’s No Light at All
Nothing. No display, no response, no life in it whatsoever. Nine times out of ten, power just isn’t reaching the unit. Check your consumer unit before anything else. A tripped breaker or RCD on that circuit cuts power completely, and ruling that out takes thirty seconds.
Here’s where people go wrong, though. Breaker trips, you reset it, it trips again immediately. Don’t keep doing that. A breaker that won’t hold is telling you there’s a fault in the circuit, and flicking it on and off repeatedly isn’t diagnosis, it’s just delaying the inevitable call.
Breaker or RCD Tripping Repeatedly
One trip, on its own? Could be nothing. Plenty of harmless reasons for a single isolated trip, so don’t spiral over it. But a breaker that goes every single time you plug in, or partway through a session, that’s different. That’s telling you something specific: a developing fault in the cable, moisture somewhere it shouldn’t be, or sometimes an issue with the car’s own charging circuit rather than the home unit at all.
This needs actual testing. Not guesswork, not repeated resets. A breaker tripping over and over is the circuit protecting itself, and whatever it’s protecting itself from needs finding before anyone touches it again.
Error Codes, Fault Lights, and What They Usually Mean
Most smart chargers won’t fail silently. They’ll show you something first. A solid red light here. A flash pattern there. Sometimes an error code sitting in the companion app. Each manufacturer does this slightly differently, so your charger’s manual or app is the fastest way to decode what that specific pattern means. And sometimes it’s nothing serious at all, just a loose connector throwing a code it probably shouldn’t.
Cable Problems: Won’t Latch, Won’t Release, Won’t Talk to the Car
A few different things fall under this one umbrella, and they tend to get mixed up, so let me separate them.
Tethered chargers lock the connector into the car during a session. That lock mechanism jams sometimes, usually in cold weather or once grit’s worked its way in. Won’t latch at all? Charging probably won’t start. Won’t release when you’re done? Check the handbook. Most cars have an emergency release procedure for exactly this, and it’s worth knowing before you’re stuck in the cold figuring it out on the fly.
Separately, sometimes everything connects physically fine and still nothing flows. That’s usually a handshake issue between charger and car, not a cable problem at all. A software hiccup on either end, a connector not quite seated, occasionally a fault that sits with the car instead. Unplug it, reconnect, push it fully home. That alone fixes more of these than you’d expect. Still happening on the same car after several tries? The vehicle’s the more likely culprit, not the charger.
The App Shows Nothing, But Is That the Real Problem?
Often, no. Smart chargers lean on WiFi to show live status, run schedules, sometimes even authorise a session before it’ll start. A dropped connection, a router that got renamed or swapped, an app that needs an update, any of these can make a perfectly healthy charger look dead on your phone while it’s charging just fine the whole time.
Quick test: is power actually being delivered even though the app shows nothing? If yes, that’s a reporting problem, not a charging fault, and the fix is completely different.
It Starts, Then Stops Partway Through
This one unsettles people more than it probably should. A session that cuts out partway through usually means something’s interrupting it, not that the charger’s broken outright. Most of the time it’s load management, the rest of the house drawing a lot of power briefly, which is a safety feature doing exactly what it’s meant to. Less commonly, it’s an overheating trip, a connection working its way looser under everyday vibration, or something genuinely developing in the circuit. Worth ruling those out if it’s a pattern and not a one off.
No Trigger, No Warning, Just Stopped
Sometimes there’s genuinely nothing to point to. Worked yesterday. Doesn’t today. Nothing changed in between. This is usually where something’s failed for real: a relay inside the unit, a terminal that’s worked itself loose over months, a component reaching the natural end of its life. Rarer than the issues above, but it’s the category that needs someone there in person instead of more back and forth over the phone.
How I Work Through It
Simplest explanation first, always. Power reaching the unit, nothing tripped at the consumer unit, that’s step one. Then the cable and connector get checked by hand, then I test whether the fault follows the car or stays with the charger, then I look at whatever diagnostics or error history the unit’s holding onto. Parts and deeper electrical work only come into it once the straightforward stuff’s been ruled out. Most visits get sorted within that process. Full replacements are rare.
Two quick stories, since they show how different the same symptom can look underneath.
A homeowner in Watford called about a charger that “just stopped” overnight. No warning. No change in routine. Breaker fine, no error light, just dead when the cable connected. Turned out a terminal inside the enclosure had worked loose over about eighteen months of ordinary vibration and heat cycling, until it finally let go for good. Re-terminated, torque checked, running fine since.
Tower Hamlets was stranger. RCD tripping, but only on damp mornings. Never on dry ones. Water had been working its way into the outdoor cable gland slowly enough that it only caused a leakage fault under certain conditions. The kind of intermittent fault that’s basically impossible to diagnose from a phone call. Resealing the gland fixed it outright.
Checks You Can Safely Do Yourself
A handful of things are safe to try before you call anyone. Confirm the breaker and RCD haven’t tripped, since that single check explains a huge chunk of “completely dead” complaints on its own. Look over the cable for cracking, damage, or dirt lodged in the connector, and make sure both ends are pushed fully home. Open the app, check it’s on WiFi, and see if there’s a firmware update sitting there unapplied. If you’ve got access to a second cable or a different car, try it, since that tells you fast whether the fault’s riding with the vehicle or staying put with the charger.
Write things down before you pick up the phone. What did the light do, and in what order? Did it work the day before? Has anything else in the house changed lately, a new appliance, electrical work elsewhere, a storm, a power cut? That one detail can cut a diagnostic visit down considerably.
Does Weather Have Anything to Do With It?
More than people assume, honestly. Damp mornings, as the Tower Hamlets case shows, can surface a fault that stays hidden the rest of the time. Cold weather stiffens cables and makes connectors jam more easily. Heavy rain finds its way into gaps that were never a problem in summer. None of this means your charger’s badly made. It means outdoor electrical equipment interacts with weather, and a fault that only shows up under specific conditions is still a real fault, just a harder one to catch.
If a problem only ever shows up after rain, or only on cold mornings, mention that when you call. It narrows things down a lot faster than “it’s not working” on its own.
When the Same Fault Comes Back After a Repair
This happens more than you’d think. Charger gets fixed, runs fine for a week or two, then the exact same symptom reappears. Usually that means the first repair treated a symptom, not the actual cause underneath it.
A terminal re-tightened without anyone asking why it loosened in the first place is a classic example. Maybe it’s just wear. Maybe there’s a vibration source nearby working it loose again, a bracket, a nearby appliance. Same logic with a resealed cable gland that nobody checked for the actual reason water got in to begin with, a crack, a gap, bad routing letting rain pool where it shouldn’t.
Tell us if a fault’s come back after a previous fix. That single piece of information changes how the visit goes. Instead of repeating the original fix, we’ll dig for whatever’s underneath it, because a repeat fault almost always means the root cause is still sitting there, untouched.
Workplace and commercial installations run into all the same issues, just multiplied across more units. Our guides on workplace EV charger installation and commercial EV charger installation go into that bigger picture, where shared load management across several bays makes tracing one specific fault a bit more involved.
Worth Checking the Electrics Even When Nothing’s Wrong Yet?
Yes, especially if your home’s electrics haven’t been looked at since the charger first went in and your household’s power use has shifted since. Our guide on preparing your home’s electrical system for an EV charger installation covers what that kind of check involves.
What You’ll Pay for a Diagnostic Visit
Depends entirely on what turns up, same as any fault finding work. Our page on EV charger installation cost walks through our general pricing, and our guide on EV charger installation labour cost breaks down labour if a repair ends up being needed on top of the visit itself.
Leave the Consumer Unit Alone
Whatever’s going on, don’t start poking around inside the consumer unit or the charger’s own enclosure. Our guide on whether you can install an EV charger yourself explains why that work needs a qualified electrician, and the same logic applies just as much to fault finding as it does to the original install.
How We Handle Every Visit
Same process, every single time, regardless of what’s been reported over the phone. Power checked, connections checked, the charger’s own diagnostics pulled, before anyone assumes parts are even needed. We run a 7 day turnaround once booked, so you’re not sitting around for weeks wondering. Request a quote and we’ll take a proper look rather than guessing blind over the phone.
We install and service chargers across Croydon, Barnet, Richmond upon Thames, Ealing, Watford, Westminster, Wandsworth, Waltham Forest, Tower Hamlets, and Sutton. Same
Quick Answers
No lights at all on the charger. First thing to check?
Your consumer unit. A tripped breaker or RCD on that circuit cuts power entirely, and it’s the quickest thing to rule out.
Should I keep resetting a breaker that keeps tripping?
No. If it trips again right after resetting, stop and get it looked at properly. Repeated tripping means the circuit’s protecting itself from a genuine fault underneath.
My app shows the charger offline. Is it actually broken?
Not necessarily. Could easily be a WiFi or connectivity hiccup rather than a real charging fault. Check whether power’s still flowing even with the app showing nothing.
Why does charging sometimes just stop partway through?
Usually load management responding to other appliances drawing power at the same time. A safety feature, not a breakdown. If it’s happening regardless of what else is running, that’s worth a proper look.
Could my car be the actual problem, not the charger?
More often than you’d think. If the charger works fine with a different car, or the fault follows your car to a different charger, the vehicle’s the more likely cause.
Is a cable that won’t latch a sign of something worse?
Not always. Cold weather and grit in the connector are common and harmless. If it’s happening consistently in normal conditions though, get that checked properly.
Do all of these need an electrician?
No. Checking the app, the cable, or whether a breaker’s tripped is fine to do yourself. Anything inside the consumer unit or the wiring itself needs a qualified electrician, no exceptions.
How fast can someone come out?
We run a 7 day turnaround once booked, and most faults get identified within that same visit.
Charger Not Working and Not Sure Why?
No need to guess from a forum thread, and no need to brace for the worst either. Get in touch through our contact page and we’ll talk through what’s likely going on before anything gets booked in.

